• Confirm that the eye area is clean, dry, and free from irritation, infection, or injury. Do not apply lashes when the eyes or surrounding skin are compromised.
• Apply a thin, continuous layer of adhesive along the lash band. Add a very small amount at the inner and outer corners if those areas commonly lift.
• Wait approximately 10–20 seconds, or until the adhesive becomes tacky rather than wet. Actual tack time may vary with the amount applied and the surrounding conditions.
• Look slightly downward and position the lash band close to the natural lash line. Do not place adhesive inside the eye, on the waterline, or directly onto the natural lashes.
• Press the center of the band into position, followed by the inner and outer corners.
• Hold gently for approximately 3–5 seconds, then allow the adhesive to set completely before touching the lashes or completing the eye makeup.
• To remove, soften the adhesive with a compatible eye-area makeup remover. Slowly lift the band from the outer corner while supporting the skin.

Important: This is a temporary strip-lash adhesive. Do not use it for professional eyelash extensions, individual semi-permanent extensions, or any multi-day bonding method

• Applying the lash while the glue is still wet → Wet adhesive allows the band to slide out of position. Wait until it develops a tacky consistency.
• Applying too much adhesive → Excess product takes longer to set and may spread beyond the lash band. Use one thin, continuous layer.
• Skipping the lash-fitting step → A band that is too long can lift at the corners or cause discomfort. Measure and trim it before applying adhesive.
• Applying glue directly to the eyelid or natural lashes → This reduces application control and may complicate removal. Apply the adhesive only to the lash band.
• Placing the band on the waterline → The adhesive must remain outside the eye and away from mucous membranes. Position the band near—but not inside—the natural lash line.
• Using it as an extension adhesive → Strip-lash glue is not formulated for professional semi-permanent extensions. Use only for the applications validated on the product label.
• Assuming latex-free means allergy-free → Other ingredients may still cause an individual reaction. Stop use immediately if irritation develops.
• Pulling the lash off without softening the glue → Forceful removal can pull natural lashes or stress the eyelid. Use a compatible remover and peel slowly.
• Sharing the applicator or touching the nozzle to skin → Contact can contaminate the product. Keep the nozzle clean and do not share personal eye cosmetics.
• Using glue that has changed in odor, color, or texture → A noticeable change may indicate contamination or deterioration. Discontinue use and replace the product.

Product type — Water‑based temporary strip‑lash adhesive.

Intended use — Temporary cosmetic lash application.

Dry‑down — Clear.

Finish — Flexible adhesive film.

Suggested tack time — Approximately 10–20 seconds; follow the verified label.

Suggested press time — Approximately 3–5 seconds.

Compatible styles — Strip lashes, half lashes, corner lashes, and compatible temporary band‑style lash segments.

Not intended for — Professional eyelash extensions or unvalidated semi‑permanent and multi‑day bonding systems.

Applicator — Precision nozzle.

Ingredients — Acrylates Copolymer, Aqua, Propylene Glycol.

Volume — 5 mL.

Caution: For external use only. Keep out of reach of children. Avoid direct contact with the eyes, waterline, inner eyelid, and mucous membranes. Do not use on irritated, injured, or infected eyes or skin. Do not use if you have a known sensitivity to any ingredient. Discontinue use immediately if redness, swelling, itching, pain, or persistent discomfort occurs. If the product enters the eye, rinse carefully with clean lukewarm water and seek medical advice if symptoms continue.

Does the adhesive dry clear?

Yes. It is intended to dry clear, although applying too much product may increase drying time or temporarily leave visible residue.

Why should I wait before placing the lash?

Allowing the adhesive to become tacky helps prevent the lash band from sliding and makes positioning easier.

How long should I wait for the glue to become tacky?

The supplied directions recommend approximately 10–20 seconds. The exact time may vary depending on application thickness and environmental conditions.

Is the adhesive waterproof or sweat-resistant?

This formula is designed with a lightweight, breathable acrylates copolymer base that provides a comfortable, natural finish. While it offers good everyday wear, it is not specifically engineered as a waterproof or sweat-proof formula.

How should the lashes be removed?

Soften the adhesive using a compatible eye-area makeup remover, then slowly peel the lash band from the outer corner. Never pull forcefully or use sharp tools near the eye.