1. Position the weighted base on a stable, flat surface within comfortable reach of your working hand.
2. Adjust the 360° gooseneck arm to angle the light directly over the area needing a flash set, such as a placed gem or nail art detail.
3. Apply or place the gel, embellishment, or art detail as needed before activating the lamp.
4. Activate the light for a 10–15 second flash cure, keeping the finger steady and in position under the light.
5. Move on to the next detail step or transition to your main curing lamp for a full, complete cure once all layers and details are in place.
6. Recharge via the included USB-C cable as needed, taking advantage of the roughly 3.5-hour charge time between uses.

• Using this lamp as a full replacement for a main curing lamp — it's designed for quick flash sets, not complete gel curing; always finish with a full cure under your primary lamp.
• Positioning the finger inconsistently under the gooseneck — uneven placement can result in an uneven flash set; take a moment to confirm steady, centered positioning before activating.
• Assuming a single flash cure fully sets a thick gel layer — this lamp is built for detail and embellishment work, not thick builder gel applications; use appropriately thin layers or embellishment placements suited to a quick flash set.
• Letting the battery run low before a mobile appointment — running out of charge mid-service can interrupt detail work unexpectedly; charge fully before appointments, especially when working outside a salon setting.
• Ignoring the 60-second auto shut-off during longer detail sessions — if you pause between flash cures for more than a minute, the lamp will power down automatically; reactivate as needed rather than assuming it stays on indefinitely.

• LED power: 3W focused LED
• Flash cure time: 10–15 seconds
• Battery: 2600mAh lithium-ion
• Battery life: Up to 9 hours of use per charge
• Charging time: Approx. 3.5 hours
• Voltage: 5V / 2A
• Auto shut-off timer: 60 seconds
• Charging cable: USB Type-C, included
• Warranty: 1-year manufacturer warranty

This is an electronic curing tool; no liquid ingredients are used, and no clinical or regulatory claims apply.

Can this lamp fully cure a standard gel polish coat on its own, or is a main lamp still necessary afterward?

This lamp is built specifically for flash curing — quick 10–15 second sets during detail work — rather than complete gel polish curing, so a full cure under your main lamp is still necessary to ensure proper hardness and durability. Treating it as a supplementary tool rather than a primary curing source will give the most reliable results.

Does the 3W LED cure the same range of gel products as a full-size lamp, or are some formulas incompatible with flash curing?

Most standard gel polishes and thin gel layers respond well to a quick flash set, but thicker builder gels or certain specialty formulas may need longer exposure than this lamp is designed to provide. Testing a small area first with unfamiliar gel products helps confirm compatibility before relying on it for a full service step.

How much does battery performance typically decline after months of regular daily use?

Lithium-ion batteries generally experience gradual capacity reduction over time with regular charge cycles, so it's reasonable to expect somewhat shorter runtime after extended daily professional use compared to when the unit was new. Charging fully rather than partially topping off frequently can help maintain more consistent battery performance over its lifespan.

Is it safe to use this lamp for gem or embellishment setting on top of gel that hasn't been fully cured yet?

Yes, that's actually one of its primary intended uses — flash curing is designed to tack down embellishments or thin gel layers just enough to hold them in place before the full cure step. Just make sure the flash-cured layer isn't relied upon as the final cure, since it's meant to secure placement rather than complete the curing process.

Does the auto shut-off feature interrupt curing if I'm working through a series of quick flash sets close together?

The 60-second timer is based on inactivity rather than cumulative session length, so as long as you're actively reactivating the lamp between flash sets within that window, it shouldn't interrupt a normal workflow. It's mainly triggered by longer pauses, such as stepping away between clients, rather than brief gaps between consecutive detail steps.